/image%2F1896381%2F20151209%2Fob_cb2b49_obd365-com.png)
OTOFIX IM1 IM2 Clone MQB Transponder via AT100
OTOFIX IM1/IM2 also clones MQB Transponder via AT100 super chip.
Go to Transponder Cloning- Volkswagen MQB Transponder Cloning
Function execution conditions
Original key
Original key CS code
AT100 transponder
Step 1: Read original key information
Step 2: Write data into the chip
Take out the original key, place the AT100 transponder in the key slot and press OK to start writing the data.
Autel K1M00 VW MQB Transponder Cloning with AT100 Super Chip
Autel MaxiIM KM100 /IM508/IM608 adds cloning function for transponders including Volkswagen MQB.
Go to Transponder Cloning->Volkswagen MQB transponder cloning
This requires AT100 super chip.
Also required to enter 16 bytes CS code. (how to get sync data using Autel)
OBDSTAR G3 Clone PSA BSI N03 on Bench
Possible to Clone PSA BSI N03 with OBDSTAR DC706 or G3?
Yes, DC706 will clone this BSI.
Review 1: I work this same bsi, and lets go finish ok.
Review 2:
100% I've read a BSI N03 with my DC706. And that was with a corrupted EEPROM and it still read.
Review 3:
Working today perfectly with a proper power supply took a while to connect. Then read and write perfect 10 mins to clone from start to finish.
OBDSTAR G3 Program Renault Koleos 2020 All Keys Lost
Renault koleos 2020 all keys lost situation.
Key: Card
Programming with OBDSTAR X300 Classic G3.
Choose free risk method.
Read pincode via dflash before using all key Lost option no problem.
Failed to program via dealer key option (programming via dump and key in OBDSTAR key sensor area): Said key successful programming but 0 key in bsi.
Choose programming key all key Lost: programming directing in ignition coil. Program successfull and 1 key bsi.
10 minutes job, car start remote good
JOB DONE.
Autel IM508 Program RAM PRO MASTER 2023 Push to Start
Problem:
I do have right now Dodge RAM PRO MASTER 2023 ( SMART KEY ) Push to start.
I got the key from the dealer from the vin number.
Autel IM508S telling me put the key next to the push start button (without pressing any buttons )
Key doesn’t need to be programmed, Car won’t accept any keys.
Any recommendations?
Solution:
Read pin under dodge and program under fiat.
It’s a hybrid between dodge and fiat.
I tried reading pin under fiat and it didnt work so i read pin under dodge and then went to Fiat 500 xl proximity to program..
OBDSTAR OdoMaster Range rover Velar 2020 Mileage Correction
How to change Range Rover Velar 2020 mileage with OBDSTAR OdoMaster or G3?
Original mileage: 84,823km
Auto detect system.
Odometer recalibiration.
Autel IM608 Failed to Program JLR K8D2 Smart Key?
Problem:
2020 Jaguar XE
K8D2 KVM 434MHZ.
Removed kvm, successfully swapped MCU and wrote data initialization with Autel IM608.
Plugged back into vehicle to learn the kvm and add keys, but got error message “The current ECU version does not support the module replacement function”
Is there anything I can do to finish this already long and painstaking effort?
Here is the clue.
K8D2 is the most problematic (cannot learn RFA or learn incorrectly or not finish the procedure). AVDI is better for K8D2 system. JLR Pluto is the best key programming device for JLR till 2024.
– AVDI Abrites – Ok (depends on the model)
– Autel- Ok (depends on the model)
– VVDI Key Tool Plus – Ok (depends on the model)
– Lonsdor – Ok (depends on the model)
— **Abrites: Key learning (No need to replace RFA)**
– JPLA – Yes (100%)
– K8D2 – Yes (100%)
– J9C3 – Yes (100%)
– M9R3 – Yes (100%)
— **Autel: RFA replacement**
– JPLA – Yes (90% success rate)
– K8D2 – Yes (70% success rate)
– J9C3 – Yes (90% success rate)
– M9R3 – No
— **Xhorse Key Tool Plus: RFA replacement (BETA)**
– JPLA – Yes (70% success rate)
– K8D2 – Yes – (50% success rate)
– J9C3 – Yes (70% success rate)
– M9R3 – No
Autel KM100 Adds Toyota RAV4 2020-2023 Smart Key Generation
Autel MaxiIM KM100 released new KeytoolDiag software on Feb. 6th, 2025.
KeytoolDiag
V2.30 2025-02-06
Version Description:
1. Adds AT100 super transponder (Autel’s own universal chip) generation function for 15 IMMO protocols (including ID46, ID48, ID4A, ID4D, IDBA, MOB, and 5C) and dedicated transponder generation menus for more than 500 models.
2. Adds smart universal key generation function for models including:
– Hyundai Tucson (2023-2024)
– Toyota GR86 (2021-2024)
– Toyota Corolla (2014-2018)
– Toyota RAV4 (2020-2023)
– Nissan Qashqai (2023)
– Acura TSX (2011-2014)
– Chevrolet Trailblazer (2012-2020)
– Chevrolet Camaro (2021-2024)
– BAIC Rubik’s Cube (2022-2024)
3. Adds cloning function for transponders including:
– ID46
– ID4C
– Toyota G (4D)
– Toyota H (8A)
– Volkswagen MOB
– GM 4A
4. Fixes other known bugs.
The updates changed the OS layout to look more like the MaxiIM lines. Looks very nice and clean. And they added a bunch of stuff.
Will this update clone MQB transponder?
You will still need 16 bytes CS code to clone MQB transponder using AT100 chip.
Autel IM508 IM608 series does not receive this upgrade yet. Keep an eye on feature updates.
CG100X V1.7.2.0 Adds Toyota BZ3 2023- 25640 BCM
CGDI CG100X new version V1.7.2.0 update details:
1. Added 16 models to dashboard.
2. Adds 4 models to RH850 decryption airbag.
3. Added 10 models to read-write.
The following models are added for dashboard.
Toyota BZ3 2023- 25640(BCM)
FOTON Landscape G5 2024- 24C16
FOTON TimeEV6 2023- R5F10DL
FOTON xiangling M2 2023- 24C16
Geely geometry G6 2022- 24C32(Multimedia host)
JAC Devos 2022- 24C08
JMC JMMC 2014- CAT1023
Chery jietu X70S 2022- 24C16(4G16)
qianjiang race Hong125 2023- 24C64
Roewe RX5 PLUS 2022- Dashboard 95640+BCM95640
Roewe EI6 2019- Dashboard 25320+BCM95640
WuLing Yunduo 2023-24C64
WuLing Hongguang EV 2022- 24C02
YAMAHA FUying 2023- 24C04
ChangAn CS35 PLUS 2022- 24C64
Zhongxing ZhongXing Pickup 2021- 24C04
The following models are added for RH850 decryption airbag
BAIC A512C00112 R7F7010643(encrypted)
Toyota 89170-08260 R7F701644(encrypted)
LINCOLN MA1T-14B321-AD R7F701A033(encrypted)
SAIC C00262208 R7F701A033(encrypted)
The following models are added for dashboard read-write.
BAIC Huansu H2E 2018- 24C04(read write)
BAIC BJ80 2016- MPC5606S(Dashboard)+95320BCM(read write)
BYD AUTO BYD Chinese 2022- 25256(Left body module)(read write)
Dayun Fengchi ZiXieChe 2022- MB96F696R(read write)
Trumpchi Hechuang Z03 2023- 24C32(read write)
Trumpchi 8040003ARRD0400 R7F7010643(encrypted)(read write)
Geely 660809888 R7F701330(encrypted)(read write)
LYNK&CO 8891944731 R7F701330(encrypted)(read write)
ChangAn Honor 2023- 9S12HY64(read write)
ChangAn 3658130XVC01A R7F7010643(encrypted)(read write)
OBDSTAR DC706 Recover GM E78 ECM via ShadowFlash
Both OBDSTAR DC706 and I/O Terminal will recover many GM ACDelco ECMs with shadow password in boot mode (check previous post).
Here is another user review on GM E78 ECM recovery using DC706.
Importance of Reading ShadowFlash in DC706:
When reading some ECUs with the DC706, the equipment gives us the option to read ShadowFlash.
Recently, while trying to clone an E78 ECU from a Silverado, the module became useless after attempting to bench write it. The writing was not possible and ECU stopped communicating by OBD (appear the code p0606 (code referring to the processor)).
However, DC706 offers us the option of writing by boot, but when trying to connect, the team requests a password. This password can be obtained by reading the ShadowFlash earlier.
Thanks to this function, it was possible to recover the ECM and avoid its loss.
Just to be clear, the option to read shadow flash does not appear in the boot menu, it is obtained by bench. If you open the delco e78/bench menu you will find the option of shadow flash.
Attached are photos of the boot mode progress.
OBDSTAR D7C06 Add DQ200 DQ250 IMMO ON, IMMO OFF, Write VIN
OBDSTAR DC706 and X300 Classic G3 update new TCM software V30.60 on Jan. 21st, 2025.
• Add JAGUAR/LAND ROVER ZF 9HP50 TC275 Read/Write INT eeprom, Read/Write INTflash, Write VIN function (BENCH)
• Add AUDI/SEAT/SKODA/VOLKSWAGEN TEMIC DQ200(0AM/0CW) DQ200-MQB TC1766 IMMO ON, IMMO OFF. Write VIN function (BENCH)
• Add AUDI/SEAT/SKODA/VOLKSWAGEN TEMIC DQ200(0AM/0CW) DQ200DXX TC1766 IMMO ON, IMMO OFF. Write VIN function (BENCH)
• Add AUDI/SEAT/SKODA/VOLKSWAGEN TEMIC DQ200 G2 TC1784 IMMO ONJMMOOFF. Write VIN function (BENCH)
• Add AUDI/SEAT/SKODA/VOLKSWAGEN TEMIC DQ200 G2-PQ TC1784 IMMO ON, IMMO OFF. Write VIN function (BENCH)
• Add AUDI/SEAT/SKODA/VOLKSWAGEN TEMIC DQ250(02E/0D9) TC1766 IMMO ON, IMMO OFF. Write VIN function (BENCH)
• Add BENZ VGS3-NAG2 special connector TCM-012 support
• Add BENZ VGS2-NAG2 special connector TCM-012 support
• Add BENZ VGS3-FDCT special connector TCM-013 support
• Add BENZ 7G DCT special connector TCM-017 support
• Add FORD/LAND ROVER/VOLVO AWF21(7G9N) special connector TCM-026 support
• Add FORD/LAND ROVER/VOLVO AWF21(AG91) special connector TCM-026 support
• Add FORD/LAND ROVER/VOLVO AWF21 (BJ32) special connector TCM-026 support
• Add FORD/LAND ROVER/VOLVO AWF21(6G9N) special connector TCM-026 support
• Add MAZDA AW6A-EL special connector TCM-026 support
• Add AEOLUS TF-70SC special connector TCM-026 support
• Add GM/OPEL/SAAB AF40-6 special connector TCM-027 support
• Add VOLVO AW55 special connector TCM-027 support
• Add CITROEN/DS/PEUGEOT AX6III special connector TCM-027 support
• Add SUZUKI TF-73SC special connector TCM-027 support
• Add AUDI/VOLKSWAGEN DQ400E special connector TCM-030 support
Add BENZ SIEMENS/CONTINENTAL DSM(FBS4) MC9S12XEQ512MAL C207/C292/ W166/W212/ W218/W447 3 types of part numbers(A0002703252/ A0002703352/ A0002703452) ECU Info.,Read Data,Virgin(Renew),Data Transfer,Write VIN,Write Datafunction (BENCH)
Add BENZ SIEMENS/CONTINENTAL DSM222(FBS4) MC9S12XEQ512MAL C217/W205/ W222/ W907/ W910 3 types of part numbers(A0002704252/ A0002704452/ A0002704652)ECU Info.,Read Data,Virgin(Renew),Data Transfer,Write VIN,Write Data function (BENCH)
Obdstar DC706 now supports gen1 and gen2 DQ200 reading, writing, IMMO ON, Immo off, mileage correction and write VIN functions.
Replace VW Passat B6 B7 ELV by Launch X431 IMMO Plus
VW Passat b6/b7 ELV replacement is done with Launch X431 IMMO Plus.
Steps to perform:
1: Force ignition on (if old elv is totally dead)
2: Read immo data from ecu ( from ccm you have to remove eeprom) to retrive pin code
3: 25 module perform security access login with pin code and adaptation group 51 enter again pin code( wait half minute, until vin code is shown)
CG FC200 Software Update to V1.2.5.1
CGDI FC200 ECU programmer released new software V1.2.5.1 on Jan. 15th, 2025.
V1.2.5.1 Registered Version NEW
(2025.01.15)
New Functions:
1. Added Wuling SIM2K-51.4 read/write, VIN modification, and three unready functions
2. Added Jinbei Lingdian TR40 read/write, VIN modification, and three unready functions
3. Added three unready functions of Volkswagen ECUs: MED17.1.6, MED17.1, MED17.5, MED17.5.1, MED17.5.2, ME17.5.22, MED17.1.10, MED17.5.20, MED17.5.25, MED17.5.5, EDC17CP14
4. Added three unready functions of BMW N20/N55/B38/N13 ECUs: MEVD17.2.5, MEVD17.2.4, MEVD17.2.9, MEVD17.2.P, MEVD17.2, MEVD17.2.6, MEVD17.2.G, MEVD17.2.K, MEVD17.2.3
5. Added verification function ECUs: ME7, ME7.8.8, ME7.9.7, ME7.9.71, M7.9.7, M7.9.7.1, ME7.5.20
Bug fixes:
1. Fixed the problem of failure to write PFlash data in some ME17.9.64
2. Fixed the problem of failure to backup data of Honda Keihin KEIHIN series ECU
3. Fixed the problem of PFlash verification failure of Hyundai Kia CPGDSH2.26.1
4. Fixed the VIN code change function for ME17.9.1, ME17.9.11, ME17.3.0, and EDC17C81
5. Fixed some bugs and optimized software performance
OBDSTAR Adds Fiat EGEA CROSS TIPO CROSS 2021-2024 Key Programming
OBDSTAR X300 Classic G3, X300 Pro4 and X300 Mini Fiat released new Immobilizer software update in Jan. 2025.
Fiat [Version: V43.09]
Add proximity key programming function for below models:
• FIAT EUROPE EGEA CROSS 2024-
• FIAT EUROPE EGEA CROSS 2022-2023
• FIAT EUROPE EGEA CROSS 2018-2021
• FIAT EUROPE EGEA CROSS 2015-2017
• FIAT EUROPE TIPO CROSS 2024-
• FIAT EUROPE TIPO CROSS 2022-2023
• FIAT EUROPE TIPO CROSS 2018-2021
• FIAT EUROPE TIPO CROSS 2015-2017
• FIAT MIDDLE EAST EGEA CROSS 2024-
• FIAT MIDDLE EAST EGEA CROSS 2022-2023
• FIAT MIDDLE EAST EGEA CROSS 2018-2021
• FIAT MIDDLE EAST EGEA CROSS 2015-2017
• FIAT MIDDLE EAST TIPO CROSS 2024-
• FIAT MIDDLE EAST TIPO CROSS 2022-2023
• FIAT MIDDLE EAST TIPO CROSS 2018-2021
• FIAT MIDDLE EAST TIPO CROSS 2015-2017
DR [Version: V40.00] [FIRST RELEASE]
1. Add remote key programming function for below models:
• DR1
• DR2
• DR3
• DR3 EV
• DR5
• DR6
• DR7
• DR CITY CROSS
• DR CITY VAN
• DR EVO3
• DR EVO4
• DR F35
2. Add blade key programming function for below models:
• DR3
• DR5
• DR6
• DR EVO3
• DR EVO4
• DR EVO5
• DR F35
• DR PK8
3. Add proximity key programming function for below models:
• DR3
• DR4
• DR5
• DR6
• DR7
• DR EVO3
• DR EVO4
• DR EVO5
• DR F35
• DR PK8
Enable 2024 CFMOTO CF400-8 Motorcycle ABS/TC System by OBDSTAR MS80
How to enable 2024 CFMOTO CF400-8 ABS/TC system using OBDSTAR MS80 motorcycle scanner.
Background:
This ABS/TC system of a 2024 CFMOTO CF400-8 Model is disabled after the failure of ABS system, it needs to be re-enabled after dealing with the failure.
Tools used: OBDSTAR MS80, M001A adapter
