OBD2 Diagnostic Tools

Yanhua Mini ACDP module 11 supports both BMW E series and F series 8HP EGS ISN clear function.

Here is the guide to clear F chassis 8HP EGS ISN. 

Install BMW EGS interface board

Short the CAN resistor on the OBP ICP adapter to the "CAN R JOIN" side

Connect OBP adapter with ACDP

Power up the ACDP host

Run ACDP software

Confirm the ACDP host is properly connected

Select BMW->EGS-> 8HP ISN Clear (Support F chassis)->Clear ISN

Make sure that the ACDP device is connected to the EGS module

Press OK

Confirm that the EGS supports clearing ISN and ISN is not cleared

Start to program EGS module, keep the voltage at least 13.0V during the programming process

Auto backup data

Verify and write coding data

Clear ISN data successfully

Save new EGS ISN data

Check EGS Status, it is now cleared. 

Newer Honda Accord instrument cluster has secured processor spansion mcu S6J3001. There is also a RH66 chip but the km data is not stored in it.

CG100 Prog iii is the cheapest programmer to read/write chip S6J3001. Not directly calculate mileage. YRead S6j data, send data to CG engineer to modify data, write back new data to S6J. 

Here is the instruction on S6J3001 mileage correction with cg100.

Select Instrument function->Asian cars->Honda->Accord->S6J3001 Read/Write

CG100 will show you wiring diagram

Connect CG100, and cluster with BDM4 adapter follow the diagram

Original mileage: 8,0888km

Read and save eeprom data

Send the eeprom data to CG engineer to modify mileage data, i.e 2,6666km

Write the modified data to S6J3001 chip.

 OBDSTAR App provides car, motorcycle and marine maintenance and repair guides for OBDSTAR tools.

Here is the instruction on combining obdstar tools with OBDSTAR App.

First of all, download and install OBDSTAR App by scanning QR code here.

For Android system at present. iOS App is under development.

How to Combine OBDSTAR Tools with App?

Power on OBDSTAR tool
Connect device with WiFi

Go to Settings->Device QR code

Then run OBDSTAR App, click me icon->My device
Select Device Binding and scan the QR code on your OBDSTAR device

Scan QR code to confirm device information
Check if device serial number is the same

Then press “To Bind” to combine device with App
Combine device successfully

Now you will see your device in OBDSTAR App.

Does Launch X431 X-prog3 work with xdiag, diagzone or prodiag activations?  Diagzone compatible xprog3? Is it working with prodiag? Will it work with xdiag?
These are frequently asked questions of Launch X-PROG3 (also called GIII) programmers.

X-prog3 is compatible with Multiple X-431 Series X-431 V, X-431 V+, X431 Pro5, X431 ProS, X431 Pro3s+, X-431 PAD V, X-431 PAD VII, X-DIAG Pro3 diagnostic tablets.

This programmer works not only for programming keys, but for working with ECU and gearbox.
But when comes to key programming you need to know what you doing there is not too much info in the Diagzone/Prodiag software.

What worked and failed? Here are user reviews.

*You are at your risk. We don’t provide technical support to 3rd party software.

Prodiag: Yes

It works with prodiag. Prodiag provides usb connection with virtual comport.
It works fine to read ECU and gearbox clone. For example, VAG DQ200 gearbox clone.

Diagzone: Yes

Diagzone does not provide usb connection with virtual comport.

You will need a OTG USB adapter or a tablet with micro usb port.

1).
I can confirm that it is working, test diagzone app and Launch x-prog3 on a lenovo yoga tab. successfully cloned DQ250 gearbox
Also works with OTG usb adapter for direct connection
I read eeprom and flash from new gearbox and used key method for getting immo data to transfer on new gearbox.

But after that I have to clone from old gearbox flash because new gearbox was adjusted for electronic parking brake.
Writing flash and epprom into gearbox trough usb using OTG adapter.

I have x431 pro interface with micro usb port.

2).
So far did vw/ audi dq200, mqb dq500 gearbox replacement, med17.5.20 clone. I’m using diagzone software and its working fine so far.

XDIAG: No

I’ve got xdiag and not working good with xprog, It reads cas3+ but when ask to save file you cant actuslly save It.
Prodiag works perfect. Saving file problem solved!

Thinkdiag: No
There is no usb port.

OBDSTAR P50 is a dedicated airbag reset tool servers more than 4,000 modules of airbags. 

Select Airbag latest version

You have the automatic detection option. You can choose manual function by entering part number if you have. 

Auto detection requires network connection.

P50 read the part number here: 285565RB0C, press Enter to continue. 

You can check operation instructions and pinout in OBDSTAR P50

 

 

Connect P004 adapter and jumper with airbag module follow the diagram on bench

 Some users reported that they got a problem connecting Toyota Proace 2017+ with Techstream. There is no Proace in the vehicle list. Try different techstream cables (mini vci, mangoose, vxdiag vcx nano toyota) and software versions, all the same.

Here is the clue.

Toyota Proace van is based on a PSA platform. Toyota Proace is a Peugeot Expert and Citroen Jumpy. PSA made Proace for Toyota.

For ProAce project TME has decided the adoption of PSA technical documentation and diagnostic tester.

So you cannot find Proace in Techstream. You will need Diagbox.

Techstream is for all Toyota and Lexus except Supra and ProAce. Supra needs Toyota ISTA* and Proace requires diagbox.

Where to download/get Diagbox for Proace?

Check and download ISTA & Diagbox license for Supra and Proace here.

*Toyota ISTA (which is based on the BMW ISTA) is a seperate software package from Techstream but it does need Techstream installed. It’s specifically for the new Toyota Supras since they’re made by BMW and have different ECUs.

 Godiag GD101 J2534 interface allows firmware update online. The recent firmware version V1.8 fix bugs. 

2023-03-31
1. Software update to v2.1
2. Firmware update to v1.8
Fix following bugs:
1. J2534 mode J1850 VPW TX message size extended to 4128 bytes
2. ELM327 mode can not be connected by PyOBD
3. ELM327 mode

How to Update Godiag J2534 firmware?

 

 

 

 

 

 

Connect Godiag j2534 with laptop

Run J1979 Diagnostic Tool on desktop

Press OK when update is completed.

Check current firmware version.

 What’s the difference between VNCI 6154A, original VAS 6154a and other 3rd parties 6154a VAG VW Audi Skoda Seat diagnostic tool?

Check table comparison below:

VNCI 6154A was tested working with latest ODIS-S V11 and ODIS-E V14.1. It is a new replacement of original vas 6154a. But it cannot be used as j2534 passthru.

CG FC200 ecu programmer released new software 1.1.2.0 on April 6th, 2023.

Update Content:
1. Fix the problem of engine recognition and read/write failure in GM E38, E67 and E39
2. Add GM E37, E39A, E78, E80 and E83 engine platform mode
3. GM E38, E67, E39 and E39A engines add Ext FLASH verification function
4. Add the "time repair" function of "Lovol harvester" to support the EDC17CV53 engine of Lovol harvester
5. Benz VGS-FDCT, VGS2-FDCT and VGS-FCVT gearbox add PFLASH verification function
6. Volkswagen DL501 Gen2 and DL382 transmissions add PFLASH verification function
7. Add BOSCH ST10 engine: M7.4.4, ME7.3.2, ME7.4.4
8. Fix the connection failure of DELPHI CRD3.10, CRD3.xx TC1797 and other engine platform modes

What programmer can read and write 2022 Honda Civic S6J336A MCU?

SMOK JTAG is only for Accord, with S6J3000. Stool and Mtool cannot read it either.

CG100 Prog III has this option.

Menu path: Odometer->Asian car->Honda->Civic->2021- S6J336AHTB

CG100 will only read and write this mcu. You have to contact CG100 technical support to modify data then write modified data back to mcu.

*If MCU is not encrypted, CG100 reads it without problem. If encrypted, it reads all FFF.

Follow the pinout here.

And another tools reads FF. ECU is closed by password.

Cluster: 78100-T21-A730-M1
Cluster MFG: NS (Nippon Seiki)
Car: Honda Civic 2022 (11gen)
Family: S6J336x
Full chip name: S6J336AHTB

Read also:

Toyota Honda S6J3001 Cluster Mileage Correction with CG100

What's the difference between Autel MaxiSys Elite II Pro and Elite II?

Elite II Pro MaxiFlash VCI supports built-in CAN FD and DoIP protocols. Elite II need extra adapter.

Elite II Pro supports PreSCAN & PostSCAN, Scan VIN & Scan License

Compared with Autel Elite II, Elite II Pro Upgraded Hardware:
Android 10 Operating System & 9.7'' Touchscreen (1536*2048)

Check table comparison below:

 OBDSTAR DC706 ECU/TCU/BCM programmer released new software V30.05.

Add following ECUs:

• Add ALFA ROMEO MAGNETI MARELLI 8GMF HW02 CAN MPC5553+95640 R/W eeprom, flash function; 

• Add ALFA ROMEO MAGNETI MARELLI 8GSF CAN MPC5565+95640 R/W eeprom,flash function; 

• Add ALFA ROMEO MAGNETI MARELLI 9GF CAN SPC564A70L7+95640 R/W eeprom, flash function; 

• Add ALFA ROMEO MAGNETI MARELLI IAW 5SF8 CAN ST10F269 R/W dflash,flash function; 

• Add ALFA ROMEO MAGNETI MARELLI IAW 5SF9 CAN ST10F269 R/W dflash.flash function; 

• Add ALFA ROMEO MAGNETI MARELLI MJD 8F2 CAN MPC5565+95640 R/W eeprom,flash function; 

• Add ALFA ROMEO MAGNETI MARELLI MJD 8F3 CAN MPC5565+95640 R/W eeprom,flash function; 

• Add ALFA ROMEO MAGNETI MARELLI MULTIJET MJD 6F3 KLINE MPC563+M58BW016DB +95320 R/W eeprom,flash function; 

• Add ALFA ROMEO MAGNETI MARELLI MULTIJET MJD 6F3 KLINE SPANSION MPC563+ S29CL016J+95320 R/W eeprom,flash function; 

• Add CITROEN MAGNETI MARELLI MJD 8F2 CAN MPC5565+95640 R/W eeprom.flash function; 

• Add CITROEN MAGNETI MARELLI MJD 8F3 CAN MPC5565+95640 R/W eeprom,flash function; • Add DODGE MAGNETI MARELLI 8GMW CAN MPC5565+95128 R/W eeprom,flash function; 

• Add FIAT MAGNETI MARELLI 9GF CAN SPC564A70L7+95640 R/W eeprom,flash function; 

• Add FIAT MAGNETI MARELLI 8GSF CAN MPC5565+95640 R/W eeprom,flash function; 

• Add FIAT MAGNETI MARELLI 8GSW CAN MPC5565+95640 R/W eeprom.flash function; 

• Add FIAT MAGNETI MARELLI 8GMW CAN MPC5565+95128 R/W eeprom,flash function; 

• Add FIAT MAGNETI MARELLI 8GMF HW02 CAN MPC5553+95640 R/W eeprom.flash function; • Add FIAT MAGNETI MARELLI MJD 8F2 CAN MPC5565+95640 R/W eeprom,flash function; 

• Add FIAT MAGNETI MARELLI MJD 8F3 CAN MPC5565+95640 R/W eeprom,flash function; 

• Add FIAT MAGNETI MARELLI IAW 5SF.XX KLINE ST10F280 R/W dflash,flash function; 

• Add FIAT MAGNETI MARELLI IAW 5SF3 KLINE ST10F280 R/W dflash.flash function; 

• Add FIAT MAGNETI MARELLI IAW 5SF3 CAN ST10F280 R/W dflash,flash function; 

• Add FIAT MAGNETI MARELLI IAW 5SF8 CAN ST10F269 R/W dflash,flash function; 

• Add FIAT MAGNETI MARELLI IAW 5SF9 CAN ST10F269 R/W dflash,flash function; 

• Add FIAT MAGNETI MARELLI IAW 4AF HW204 KLINE ST10F168+95160 R/W eeprom,flash function; 

• Add FIAT MAGNETI MARELLI IAW 4AF HW407 KLINE ST10F269+95160 R/W eeprom.flash function; 

• Add FIAT MAGNETI MARELLI IAW 59F HW<100 CPU32 KLINE 29F200BB+95080 R/W eeprom,flash function; 

• Add FIAT MAGNETI MARELLI IAW 59F HW303/HW306 KLINE ST10F168+95160 R/W eeprom, flash function; 

• Add FIAT MAGNETI MARELLI IAW 59F HW603/HW606 KLINE ST10F269+95159 R/W eeprom, flash function; 

• Add FIAT MAGNETI MARELLI IAW 5AF HW303/HW306 KLINE ST10F168+95160 R/W eeprom, flash function; 

• Add FIAT MAGNETI MARELLI IAW 5AF HW603/HW607 KLINE ST10F269+95160 R/W eeprom, flash function; 

• Add FIAT MAGNETI MARELLI MULTIJET MJD 6JF KLINE MPC555+95320 R/W eeprom.flash function; 

• Add FIAT MAGNETI MARELLI MULTIJET MJD 6F3 KLINE MPC563+M58BW016DB+95320 R/W eeprom,flash function; 

• Add FIAT MAGNETI MARELLI MULTIJET MJD 6F3 KLINE SPANSION MPC563+S29CL016J+ 95320 R/W eeprom.flash function; 

• Add FIAT BOSCH ME7.3.1 KLINE BOOTPIN 29F400BB+95080 R/W eeprom.flash function; 

• Add FIAT BOSCH ME7.3.H4 KLINE BOOTPIN 29F400BB+95080 R/W eeprom.flash function; 

• Add FORD MAGNETI MARELLI 9GF CAN SPC564A70L7+95640 R/W eeprom.flash function; 

• Add FORD MAGNETI MARELLI MJD 8F2 CAN MPC5565+95640 R/W eeprom.flash function; 

• Add FORD MAGNETI MARELLI MJD 8F3 CAN MPC5565+95640 R/W eeprom.flash function; 

• Add FORD MAGNETI MARELLI MULTIJET MJD 6F3 KLINE MPC563+M58BW016DB+95320 R/W eeprom.flash function; 

• Add FORD MAGNETI MARELLI MULTIJET MJD 6F3 KLINE SPANSION MPC563+S29CL016J +95320 R/W eeprom.flash function; 

• Add IVECO MAGNETI MARELLI IAW 5SF8 CAN ST10F269 R/W dflash,flash function; 

• Add IVECO MAGNETI MARELLI IAW 5SF9 CAN ST10F269 R/W dflash,flash function; 

• Add JEEP MAGNETI MARELLI 9GF CAN SPC564A70L7+95640 R/W eeprom.flash function; 

• Add LANCIA MAGNETI MARELLI 8GSF CAN MPC5565+95640 R/W eeprom.flash function; 

• Add LANCIA MAGNETI MARELLI 9GF CAN SPC564A70L7+95640 R/W eeprom,flash function; 

• Add LANCIA MAGNETI MARELLI IAW 5SF8 CAN ST10F269 R/W dflash,flash function; 

• Add LANCIA MAGNETI MARELLI IAW 5SF9 CAN ST10F269 R/W dflash,flash function; 

• Add LANCIA MAGNETI MARELLI MJD 8F3 CAN MPC5565+95640 R/W eeprom.flash function; 

• Add LANCIA MAGNETI MARELLI MULTIJET MJD 6F3 KLINE MPC563+M58BW016DB+95320 R/W eeprom,flash function; 

• Add LANCIA MAGNETI MARELLI MULTIJET MJD 6F3 KLINE SPANSION MPC563+S29CL016J +95320 R/W eeprom.flash function; 

• Add LANCIA MAGNETI MARELLI MULTIJET MJD 6JF KLINE MPC555+95320 R/W eeprom, flash function; 

• Add OPEL MAGNETI MARELLI MJD 8F3 CAN MPC5565+95640 R/W eeprom.flash function;

 • Add PEUGEOT MAGNETI MARELLI MJD 8F2 CAN MPC5565+95640 R/W eeprom.flash function; 

• Add PEUGEOT MAGNETI MARELLI MJD 8F3 CAN MPC5565+95640 R/W eeprom.flash function; 

• Add TATA MAGNETI MARELLI MULTIJET MJD 6F3 KLINE MPC563+M58BW016DB+95320 R/W eeprom.flash function; 

• Add TATA MAGNETI MARELLI MULTIJET MJD 6F3 KLINE SPANSION MPC563+S29CL016J +95320 R/W eeprom.flash function; 

• Add VAUXHALL MAGNETI MARELLI MJD 8F3 CAN MPC5565+95640 R/W eeprom,flash function.

 Problem:

I need to add a new key to Renault Kadjar 2016 smart card with NCF29A1M transponder by OBDSTAR X300 DP Plus.
Read dflash ok
Make dealer key ok
Add key failed!
Failed to read pin.
Customer card works.
Wondering if following below instructions is safe.
If I will use AKL option and non pin will be correct the customer card will not work. Am I right?

Solution:

Kadjar does not work through the Add key menu, it is done through AKL (all keys lost).

You always have to go through all keys lost and program original key after you read data then you can code original and new key second time.
This is process
Read flash
Save flash
All keys lost
program keys
Then Pre code new key
Program keys
Job done.

Always use battery support for read dflash and keep internet connection stable.

 VAG ODIS-S service software V11 downloaded for free.

ODIS V11 software download

Password: 8888

Software version: ODIS V11+ PostSetup

Operating system: Win7, Win10

Language: English, German, Spanish, French and Korean

Supported car brands: Audi, Skoda, FAW-Volkswagen, Volkswagen, Shanghai Volkswagen, Volkswagen Commercial, Bugatti, Lamborghini, SEAT, MAN, Bentley

Compatible device: VNCI 6154A

Free to test it with svci 6154a, vas 6154a etc by your side.

NOTE: This ODIS v11 does not work with vxdiag vcx se 6154 because it uses different driver.

VNCI 6154a vs VAS 6154a vs other 6154a 

What’s new in VNCI 6154A?

• Work with original driver, Don’t need driver manager.
• Supports DoIP & CAN FD protocol
• With base station/hotspot mode switching button.
• Free license until 2030 year

 This is a 2020 Chevrolet Silverado with blade key. Here you can add key but the guy said that he wants to erase all the keys, so we are gonna go to all keys lost procedure.

You can add key even if you don’t have a working key on chevy, Adding a key doesn’t delete current keys programmed to the vehicle.

** NOTE:

1.Make sure battery fully charged, this is highly recommended, if battery isn’t fully charged there is a possibility that vehicle won’t start.

2.If it is smart proximity, IM608 won’t calculate security code directly. This is blade key, so it will calculate pin.

How to Calculate GM 24-Digit Security Code by Autel IM508 IM608 Team?

Connect Autel IM608 with USB and enable WiFi connection

Select GM->Automoatic selection

Confirm vehicle information

Select Blade key

Do a Immo status scan

Turn on ignition switch
Select All keys lost

Follow 3 steps to program key

Step 1: Read PIN

This function requires network connection

Read 4-digit pin successfully.

Step 2: Clear DTC
Step 3: Learn key

Learn key requires 4-digit pin.

Follow IM608 promts to turn ignition on, open/close driver door until key learning completed.