/image%2F1896381%2F20151209%2Fob_cb2b49_obd365-com.png)
KT200 Software Update with Patch
Here is the official guide to update KT200/KTM200/ECUTuner ecu programmer software.
KT200 will prompt new version available when there is a new version. Press OK and follow steps below to run an upgrade.
Download the latest patch and dfb2xx.ll here
https://mega.nz/file/Mbs3XBwY#Ia3erk1QfYFLk5P8fO9JlU3rHBK5fE2Smo2oXGuG0Zo
Unexact zip file
Load and install the Patch
Copy dfb2xx.dll to replace the specified folder file
Copy and paste dfb2xx.dll to C:/KT200-master/DFBTech_Driver/i386 folder
If your system is 32bit, copy and paste dfb2xx.dll to C:/Windows/System32 folder
If your system is 64bit, copy the dfb2xx.dll file to C:/Windows/SysWOW64 folder
Then run KT200 software again.
Update KT200 software finished. New version software is ready to use.
https://www.obdii365.com/service/install-kt200-ecu-programmer-software.html
How to Correct Toyota Hilux 93C66 Mileage with Digimaster 3?
What’s the best tool for reading and writing mileage for Toyota Hilux eeprom?
Yanhua Digimaster 3 is the best mileage programmer for Toyota brand. D3 will do all new and old Hilux with 93*** eeprom (93c56, 93c66 etc).
Digimaster3 will correct mileage for Hilux as well as other Toyota in 2 ways.
Or auto detect vehicle and cluster type (read by chip)
1. OBP Mode
OBP mode requires removing eeprom IC chip and solder it to OBP adapter of D3
Then read and write eeprom to correct odometer
2.ICP Mode
Can be done in circuit. The way will make wire links to the eeprom instead of removing the chip all the time when making corrections.
Connect flat cable to ICP adapter follow the wiring diagram
Digimaster3 Hilux 93C66 IC wiring diagram
NOTE:
OBP, ICP and 8-pin flat cable are all included in digimaster iii.
Reset 2005 Crossfire SRT6 TPMS by Micropod2 DRB3
Just wanted to report the recent successful use of the Micropod 2 clone and DRBIII software that many users have recommended.
I only used this to reset the TPMS to clear the dash light and recognize four new Schrader 20028 sensors on my 2005 Crossfire SRT6.
I would like to thank obdii365.com regarding the specifics of what to buy and how to get it to work.
The steps to do the TPMS reset is very helpful
http://blog.obdii365.com/2021/02/19/2007-chrysler-crossfire-tpms-relearn-using-drb3-and-micropod-2/
For reference I did not have to modify my Micropod, and I used a doughnut magnet to trigger the sensors as prompted, so I did not need a separate scanning tool. I purchased my Micropod from the OBDII365.com website per the link that many have recommended. (It did come with all software needed, for $135.) I also followed the posted instructions regarding recommended computer and procedure to load the software. I would have never figured this out on my own.
I am located in the southern Va. if anyone in the area may want help in resetting their TPMS light after installing new sensors. We’ll give it a try.
How to Transfer Data from Xtool X100 PAD3 to PC?
Question:
How do you get your immo bin files in and out of your Xtool x100 Pad3?
Are there some kind of PC software that you connect to the Pad3?
X100 Pad3+ KC501.
Answer:
In case anyone need, here is how to.
you need to transfer the files from internal storage to external storage.
From xtool app go to file manager and then copy your dump (it is saved in a map called “adapter”) to external storage. Download a file manager to sent the file or use usb cable to connect pc.
USB Xtool to USB PC E:\Diagnosis\traces\PS_ADAPTER-V19.05 Copy or paste here.
CG FC200 1.0.9.0 Update GM ACDelco and ZF 9HP
CG FC200 ECU programmer released new software version 1.0.9.0 on Oct. 19th 2022.
CG FC200 Software V1.0.9.0 NEW
(2022.10.19)
1. Added GM ACDelco ECU: E38, E39, E67
- ACDelco E38：read and write EEPROM & FLASH
- ACDelco E39：read and write FLASH, read password
- ACDelco E67：read and write EEPROM & FLASH
(Note: please update the authorization for the first time, and then restart the software)
2.New gearbox computer: ZF_9HP
Read and write EEPROM and Flash
Models involved: Acura, Chrysler, Citroen, DS, Peugeot, Dodge, Fiat, Honda, Jaguar, Jeep, Land Rover
3. Added Bosch engine (platform mode): MD1CS018, MG1CS032, MG1CS026, MG1CA920, MG1CA007, MG1CA811
4. Added engine with modified VIN function: EDC17C42, EDC17CP27, MED17.8.2, MEVD17.2.7
5. Added the American version of BMW 28A0 and 101F fault code shutdown function
6. Fix the abnormal display of software service time
7. Fix some bugs and optimize software performance
Which Tool for Toyota Tundra 2019 Airbag Crash Reset?
I need to clear crash data for Toyota Tundra 2019? Which tool will do this?
Airbag
Toyota 89170-0C583
335384-110
You can also read airbag data with programmers, i.e vvdi prog, orange5 etc. Here are the pinouts.
KT200 Pinout to Bosch EDC17CV41
Here is the guide to read BOSCH EDC17 CV41 [ 1797 ] - [Diesel] Challenger, Claas, Isuzu, Iveco, JCB, Man, Massey Fergusson, New Holland, Valtra ECU with KT200.
CV41 has 2 possible S1 S2 pinouts for GPT. Connect the multi-function cable as follows. For this ECU there are 2 different types of hardware versions, try the following 2 combinations in series. The ECU will not suffer any damage during connection tests.
No. 1
No.2
Some ECUs enter bench mode with the pinout below
To read and write use the following driver:
→ BENCH MODE
→ [brand]
→ TC1797
– [brand]
→ EDC17 CV41
Launch X431 Xprog3 Benz All Keys Lost Ask for MCU3 Adapter?
Question 1: Someone has an adapter for reading GM ACDelco ecus with Launch X431 X-prog3?
Question 2: Launch has the wiring diagram to a part that’s not included with the xprog3. Where can i get the adapter for xprog3 mcu3?
Question 3: Just gone to do MB SIM4LKE ecu and diagram shows a box with k2 connection which I haven’t got. Anyone any idea?
Answer:
All functions above require a Launch MCU3 adapter.
The mcu3 adapter is not included with the xprog3/GIII programmer.
The MCU3 adapter is used to read new ECUs and TCUs as well as Mercedes Benz all keys lost.
The adapter is available in obdii365.com now.
https://www.obdii365.com/wholesale/launch-mcu3-adapter-for-x-prog3.html
Applications and advantages of the new Launch MCU3 adapter
- ADAS Advanced Driving Assist System
- Audi VW MQB gearbox replacement
- BMW continental msv90 engine ecu replacement and cloning
- Peugeot Key Programming
- Mercedes Benz transmission deleted and operating instructions vgs nag2 vgs2 nag2 and vgs3 nag2
- Mercedes Benz w164 2009 Key Programming
- Volkswagen Audi 5th generation engine reading engine data via direct connection and online programming and coding
- For BMW E chassis 8hp EGS deleted
- BMW 8hp chassis F and G delete function
- Key programming cas4/cas4+ all keys lost and adding keys
- Programming cas1 cas2 cas3 cas3+ lost keys and add key
- CAS4 immobilizer module replacement
- Replacement of Volkswagen Audi engine and reading data med17 and edc17
- Mercedes Benz med9.7 ecu deleted
- Volkswagen Audi Replacement 4th Generation Instrument Replacement
- Engine replacement for Volkswagen Audi MED17.5.22
- Programming of lost keys and adding key Porsche Cayenne 2011 2017
- Cloning and virginization e39 ac delco
- Power shift cloning and virginization
- Nissan ecu and Tcm conversion and virgin ecu programming and calibrations
- Special features in Chrysler and registration at autoauth FCA sgw
- Special features in GM and Ford
How to Solve KT200 Cannot find DFB2XX.dll Problem?
Problem:
I had a problem installing KT200 2022.10.01 software, error cannot find DFB2XX.dll. Reinstall software still no luck, any solution?
Solution:
Download dfb2xx.rar file and unzip
For 64bit system, paste DFB2XX.dll to C:\Windows\SysWOW64 folder
For 32bit system, paste DFB2XX.dll to C:\Windows\System32 folder
How to Change OBDSTAR MK70 Language?
OBDSTAR MK70 motorcycle key programmer supports mulit-language, including: English, Spanish, Russian, Thai, Turkish, Farsi (Persian), French, German, Polish, Italian, Indonesian, Hebrew, Vietnamese.
Default language is English.
How to change OBDSTAR MK70 language?
1. After receive the device, send device serial number to your dealer
2. Connect MK70 with network
3. Login OBDSTAR account with user name and password
4. Press VCI, select language you desired
5. Press DP icon, perform one-key upgrade
6. Your device language is upgraded too.
Renolink V2.0 Software Free Download
Renolink software version 2.00 is available and works on the original and Chinese Renolink OBD2 Renault cables.
Autel IM508 Nissan Rogue 2017 Not Start Solution
This is a Nissan Rogue 2017. Just added a spare proximity key with Autel IM508 but bricked it. Pushing start does nothing. VIN is NA when scanning ships ecu and ECU NA. BCM is fine. When read pin everything went dead. BCM I have is not on the bad list. Any solution?
Solution:
You did not brick the BCM. Long battery reset, VIN number will come back in a few minutes.
Battery reset and test, disconnect both terminals, leave for 15-20 minutes and re connect, re-scan to test.
If the BCM went to sleep on you, try disconnecting both battery terminals and touch them both together for few minutes, if that doesn’t work try leaving both battery terminals disconnected for about 45 minutes.
Feedback:
45 minutes worked with key pressed to start afterwards and held and had to reprogram original key of course. I have managed to successfully get the job done with im508.
How to Solve KT200 Software 2022.10.01 Not Working?
Problem:
I am installing KT200 software version 2022.10.01 from the manufacturer's website but the program does not work.
When I install the older version from August, downloaded from the seller's website, the program starts
What's the problem and how can I update to the new version ???
Solution:
http://blog.obdii365.com/2022/09/30/free-download-kt200-2022-10-01-software/
Read and Write Volvo Euro 6 TRW EMS2.3 with KT200
KT200 full version ecu programmer reading and writing an Euro 6 Volvo ACM with JTAG... 100%
I don´t have here the writing picture, but trust me.. it works!!!!
This truck has an ECU TRW EMS2.3, read/write without problems, however, checksum can not be done. Use WinOls to do it.
EMS 2.3 R/W without problems... 100% working, only the checksum can not be performed, use winols to do it.
Can I Generate Xhorse Super Chip with Autel KM100?
Q: I bought an Autel KM100 I’m trying to generate a chip I tested it with a xhorse vvdi super chip xt27a but it doesn’t work. Does anyone know what type of Chip is appropriate to be able to generate?
Answer:
Autel will not generate Xhorse chips or KEYDY, Autel must have its own chips or Autel remotes.
In the same way, Xhorse does not generate Keydy chips or vice versa.
Autel only generates AUTEL universal remotes.
